输注速度,speed of intravenous infusion
1)speed of intravenous infusion输注速度
1.Osmotic pressure,pH value,stimulation,toxicity and thespeed of intravenous infusion are the critical causes of phlebitis.目的输液带来的静脉炎等问题是护理工作的难点,药物的渗透压、pH值、刺激性、毒性及输注速度是导致输液性静脉炎的重要原因。
英文短句/例句
1.Influence of different types of infusion set on infusion speed of cephalosporin antibiotics and on the occurrence of phlebitis of patients不同类型输液器对头孢类抗生素输注速度及静脉炎发生情况的影响
2.ARE BOTH INPUT AND OUTPUT SPEED READINGS GREATER THAN 0 RPM?输入速度和输出速度是否都大于０ＲＰＭ？
3.REPAIRING OUTPUT SPEED SENSOR修理输出速度感知器
4.cheap and rapid transportation收费低速度快的运输
5.DISCONNECT THE INPUT SPEED SENSOR.拆除输入速度感知器。＊＊
6.REPAIRING INPUT AND/OR OUTPUT SPEED SENSOR ERROR修复输入和/或输出速度感知器错误。
7.The wireless office landnetwork transmits the bandwidth high, the transmission speed is fast;无线局域网络传输带宽高，传输速度快；
8.Research on the Output Section of High Power Broadband Multi-Beam Klystron;大功率宽带多注速调管输出段的研究
9.The cerebral uptake of propofol following administration at a constant infusion rate;恒速静脉输注异丙酚时脑摄取的研究
10.An e-timing motor for the transport can ensure the placidity move speed.输送采用电子调速电机，运行速度平稳。
11.Pneumatic signals will travel only at sonic speeds.气动信号的传输速度仅仅相当于音速。
12.Note that the words "velocity"and "speed"require explanation.请注意，“速度”和“速率”这两个词需要解释。
13.The turbine speed must be greater than 6RPM or the output speed must be geater than 4RPM涡轮速度必须大于６００ＲＰＭ或输出速度必须大于４００ＲＰＭ
14.Poster speed and conveyer belt speed transfer speed in step , can is it stick to standard exactness and poster quality to guarantee.贴标速度与输送带速度同步调速，可确保贴标准确度及贴标品质。
15.Failed input or output speed sensor (intermittent or hard code)失败的输入或输出速度感知器（间歇的或硬代码）
16.The Clinical Study of Constant Infusion of Propofol for Total Intravenous Anesthesia;丙泊酚恒速输注全凭静脉麻醉的临床研究
17.Pneumatic conveying requires comparatively high gas velocities.气力输送需要比较高的气体速度。
18.REPAIR THE OPEN INPUT SPEED SENSE GND CIRCUIT.维修断开的输入速度感知器接地电路。＊
相关短句/例句
input speed输入速度;注入速度;进料速度
3)infusion rate输注速率
1.Intra-operative optimalinfusion rate of remifentanil for patients undergoing breast cancer radical operation乳癌根治手术患者全麻维持期瑞芬太尼最佳输注速率的研究
4)gas injection rate注气速度
5)injection rate注入速度
1.Study oninjection rate of third level formation with polymer flooding in Daqing Oilfield.;大庆油田三类油层聚合物驱注入速度研究
2.Selection of the rationalinjection rate for reservoir with polymer flooding;聚合物驱合理注入速度的选择
3.This paper uses reservoir numerical simulation method to study the effect ofinjection rate on the displacement efficiency of polymer flooding and analyzes the reason of the effect.运用油藏数值模拟方法研究了注入速度对聚合物驱油效果的影响 ,并对注入速度影响聚合物驱效果的原因进行了分析。
6)Injection Speed注射速度
延伸阅读
静脉输注静脉输注将药液输入或注射到静脉内的过程。参见"静脉注射"、"静脉输液法"和"静脉滴注"。
