刚度测试,rigidity measuring
1)rigidity measuring刚度测试
英文短句/例句
1.Research on Methods to Measure the Wrap Stiffness of Freight Bogie货车转向架抗菱刚度测试方法的研究
2.Key Technology Research of Small-Size Stiffness Measuring Instrument for Sheet Metal;小型薄板件刚度测试仪关键技术研究
3.Study on Stiffness Testing Technology of Geocell Reinforced Cushion and Its Calculation Theory格室垫层刚度测试技术及其计算理论研究
4.Cantilever method悬臂式测定法,刚软度测定法《试》(织物刚性试验)
5.Study and Development of a New Torsion Stiffness Measurement Instrument of Aerospace Micro Cylindrical Helical Torsion Spring;航天微型扭簧刚度性能测试仪的研制
6.Measurements of Deformation and Influence of Machine System Stiffness in Ice Mechanical Properties Tests冰力学实验变形测量与试验机系统刚度影响
7.The static radial stiffness of PCR tire was measured with a vibration tester.在振动试验机上测试轿车子午线轮胎的静态径向刚度。
8.Design of a New Type Test Stand for Bogie Stiffness and Research on Measurement Method一种新型转向架刚度试验台设计及测试方法研究
9.Research on Stiffness Mesurement Technique of Precision Flexibile Parts Based on Dynamic Testing基于动态测试的精密弹性元件刚度测量方法研究
10.The Test Method of Determining Residual Stress Based on Yield and Rigidity Decay;基于屈服及刚度衰减条件测定残余应力的试验方法
11.Rainbow Salon is newly built and is being tested.彩虹沙龙刚刚建成,正在测试中,还需要不断完善。
12.The Study for the Shear Test Method of the Elastomeric Bearings for Bridge and Stiffness of Testing System;桥梁板式橡胶支座剪切模量检测方法研究及抗压弹性模量测试系统刚度分析
13.The performances of drape, wrinkle recovery, bending rigidity and bulkiness are tested after the treatment.测试了酶整理前后织物的悬垂性、折皱回复性、抗弯刚度、蓬松性等性能的变化。
14.No sooner had we finished the reading quiz than the teacher gave us a vocabulary test.我们刚刚做完阅读测验,老师就让我们做词汇测试。
15.diamond pyramid hardness test维氏金刚石棱锥硬度试验
16.Vickers diamond pyramid hardness test维克斯金刚石棱锥硬度试验
17.Simulation and Experiment Research of the Door Stiffness on Automotive;汽车车门刚度的仿真分析与试验研究
18.Experimental research on torsional stiffness of steel reinforced concrete subjected型钢混凝土构件扭转刚度的试验研究
相关短句/例句
rigidity measuring instrument刚度测试仪
3)test stand for measurement of stiffness刚度测试试验台
4)torsional stiffness test扭转刚度测试
5)stiffness testing syetem刚度测试系统
6)diamond hardness tester金刚石硬度测试器
延伸阅读
测试结果可接受性的检查和最终测试结果的确定测试结果可接受性的检查和最终测试结果的确定check of the acceptability of test results and determination of the final test resultC凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差