镍基药芯焊丝,Ni-base flux-cored wire
1)Ni-base flux-cored wire镍基药芯焊丝
1.In this paper,the oxidation behavior of deposited metal for newNi-base flux-cored wire in air at the temperature of 800℃ and 1000℃ was studied by using the oxidation weight increasing method.采用增重法测定了自制新型镍基药芯焊丝熔敷金属在800℃和1000℃空气中的高温氧化行为。
英文短句/例句
1.High-temperature Oxidation Behavior of Deposited Metal for New Ni-base Flux-cored Wire新型镍基药芯焊丝熔敷金属的高温氧化行为
2.Microstructure of hardfacing metal and matrix materials with high abrasive flux-cored wire高耐磨药芯焊丝堆焊组织及基体选择
3.A Vision-Based Automatic Seam Tracking System for Underwater Flux-Cored Arc Welding基于视觉传感的药芯焊丝水下焊接焊缝自动跟踪系统
4.Solid core/drug sore welding wire conversion and arc-receiving function.实芯/药芯焊丝切换和收弧选择功能。
5.Regression and Analysis on Metal Strength of Welding Seam of Welding Core Wine药芯焊丝焊缝金属强度的回归与分析
6.Development of YCJEG50 Electrogas Welding with Flux-cored WireYCJEG50气电立焊药芯焊丝的研制
7.The Technology Test of Flux-cored Solder Wires for CO_2 Gas Shield Welding药芯焊丝CO_2气体保护焊工艺研究
8.The Development of Metal Cored Self-shielded Flux-cored Wire for Submerged Overlaying金属粉芯自保护堆焊用药芯焊丝的研制
9.Study on metal-cored wire in pipeline automatic welding process金属粉芯药芯焊丝管道全自动焊接工艺研究
10.Application and Characteristic of Shielded Flux Cored Arc Down Welding Technology药芯焊丝自保护焊下向焊技术的特点及其应用
11.The Study of the Control System to Product Line of Flux-Cored Wire;新型药芯焊丝生产线控制系统的研究
12.Development of YCJ601Ni-QL Flux-Cored Wire Used for High-Strength Low-Alloy SteelYCJ601Ni-QL低合金高强度钢药芯焊丝的研制
13.The Study on Operation Performance of Self-shielded Flux Cored Wire Used in X80 Pipeline SteelX80管线钢用自保护药芯焊丝工艺研究
14.Development Status of Production Process and Equipment of Flux-cored Welding Wire药芯焊丝生产工艺及装备的发展状况
15.Ti content on diffusible hydrogen of deposited metal of flux cored wire钛对药芯焊丝熔敷金属扩散氢的影响
16.Effect of CeO_2 Additions on Properties of Self-Shielded Flux Cored WireCeO_2对自保护药芯焊丝性能的影响
17.Development of duplex stainless steel flux-cored wire GDQA2205双相不锈钢药芯焊丝GDQA2205的研制
18.The Research of Domestic Manufacture of Cored Hard Alloy Wire for Harding Rollers;辊堆焊硬质合金类药芯焊丝应用国产化研究
相关短句/例句
flux-cored wire药芯焊丝
1.Wear resistant impact hardfacingflux-cored wire used in tool manufacture of shield machine;盾构机刀具制造用耐磨耐冲击堆焊药芯焊丝的研究
2.Analysis and evaluation of stability offlux-cored wire;药芯焊丝稳定性分析与评价
3.Application on ceramic backing andflux-cored wire in welding thick-wall clad plate;陶瓷衬垫和药芯焊丝在焊接厚壁复合钢板中的应用
3)flux cored wire药芯焊丝
1.Effect of unbalance factor on toghness of weld metal by CO_2 arc welding withflux cored wire;不平衡因子对药芯焊丝CO_2气体保护焊焊缝金属韧度的影响
2.Application offlux cored wire semiautomatic welding in the long distance transmission pipeline;药芯焊丝半自动焊在长输管道中的应用
3.Promblems met in researching offlux cored wire for submerged arc welding;埋弧堆焊药芯焊丝研制过程中遇到的问题
4)nickel base welding wire镍基焊丝
1.The test results show that it is feasible to weld HR3C steel with Thermanit617nickel base welding wire substitution for welding material YT-HR3C.首先对新型耐热HR3C钢焊接性及其所用替代焊丝Thermanit617(ERNiCrCoMo-1)的焊接性进行分析,然后采用GTAW焊接工艺,将Thermanit617镍基合金焊丝作填充材料,焊制HR3C钢管接头,并对试件接头力学性能、耐晶间腐蚀性能及组织特征等进行了测试和分析,试验结果表明HR3C钢采用Thermanit617镍基焊丝替代焊材YT-HR3C焊接是可行的。
5)flux for flux-cored wire药芯焊丝药芯
1.The principle and technology to produce amorphousflux for flux-cored wires by the sol--gel process were introduced in detail.本文详细介绍了溶胶-凝胶法制备非晶态药芯焊丝药芯的原理和工艺用Ti（OC4H9）4和Si（OC2H5）4为原料制备出了非晶态药芯，对非晶态药芯进行了X射线衍射分析、差热和热重分析结果表明：溶胶-凝胶法制备的非晶态药芯化学成分均匀、含氢量低、吸潮性小，能够满足焊接自动化生产对药芯焊丝药芯的要求，具有广阔的开发与应用前
6)ZD welding wire with agent coreZD药芯焊丝
延伸阅读
Z8612热芯盒射芯机操作规程1、遵守铸造设备通用操作规程。2、工作前还必须遵守：a、 检查设备上行程开关和碰块的位置是否正确，如不正确，必须调整。b、 接通电源，打开压缩空气伐门，先用手动方法，对各机构逐进行点动试车，然后用自动方法，进行一个循环试车，确认一切正常后，方可进行生产。3、工作中还必须遵守：a、 在设备开动后，一个循环未完成时，不许中途调整电器，以免发生误动作，造成设备人身事故；b、 设备的每一个循环后，必须用喷咀清除芯盒上残存的砂子，并喷涂分型剂；c、 在未切断电源和所气源前，不准将手伸入芯盒和夹紧器之间的空隙处，或把手放在导轨上，以免发生人身事故。d、 一般不准空射，如必须空射，一定要把压缩空气伐门关小；e、 如果用手操作，不准同时操作两个电器开关。4、工作后还必须遵守：a、 操纵各个电器开关，使设备各机构恢复到原始位置，然后切断电源和气源；b、 折下射砂头，清理积砂和粘砂；c、 清除排气塞内的粘砂；d、 取下射砂筒，清除缝隙中的粘砂，最后用石蜡涂擦内壁，但不要将缝隙堵塞；e、 清除闸板上的积砂，并在闸板上涂石墨粉，以减少磨擦；f、 清除导轨和导杆上的积灰和积砂，并涂上一层润滑油。
