侧压,lateral pressure
1)lateral pressure侧压
1.Experimental study of concrete fatigue in tension under alateral pressure;单侧压下混凝土受拉疲劳试验研究
2.Variable-amplitude fatigue tests for concrete in tension under single and bi-lateral pressures are conducted.本文进行了混凝土分别在单、双向侧压作用下受拉变幅疲劳试验,得到了疲劳寿命和残余应变。
英文短句/例句
1.The low side pressure is too high, and the high side pressure is too low.低侧压力过高，高侧压力过低。
2.slabbing action板坯的垂直压下或侧压下
3.Analysis of transcritical R23 heat pump systemR23跨临界循环最优高压侧压力分析
4.Numerical simulations of curved surface sidewall compression scramjet inlets with varied sweep angle and sidewall compression angle变后掠角+变侧压角曲面压缩的高超侧压式进气道数值仿真
5.Experimental study on the dynamic biaxial compressive properties of concrete under constant confining pressure定侧压下混凝土双轴动态抗压性能的试验研究
6.Calculation of Secondary Voltage According to Primary Voltage of On-Load Transformers由负载变压器原边侧电压计算付边侧电压
7.unconfined compression test无侧限压缩[压力, 抗压]试验
8.the pressure point is on the inner part of the upper arm,那么施压点在上臂内侧，
9.Study on Lateral Compression Pressing of Tin Bronze for Continuous Extrusion基于连续挤压的锡青铜侧向挤压研究
10.If the appendix is lateral to or behind the cecum, the tenderness may be in the right flank.若阑尾在盲肠的侧面或后面，压痛可在右侧。
11.CAD System Research of Side hydraulic Pressune Jar in Extrusion Modeling Presses Based on SolidWorks基于SolidWorks挤压成形液压机侧液压缸CAD系统研究
12.Preliminary Discussion on Low-voltage Side Single-phase Earthing Protection of Medium-voltage Distribution Transformer中压配电变压器低压侧单相接地保护浅析
13.The adoption liquid of left right side urn presses the synchronous way, and guarantee the synchronous headway of left right side urn to squeeze.左右侧缸采用液压同步方式，保证左右侧缸同步前进挤压。
14.In the right orbit, an external ethmoidectomy was done, while in the left, a transnasal endoscopic approach was used to remove the inferomedial wall.两边皆以外侧眼眶切开术行外侧眼窝减压术合并内侧及部分眼窝底减压术。
15.If the high-side or low-side voltages vary over a wide range during the load cycle, it may be necessary to provide bus regulation.若在负荷变化周期中,高压侧或低压侧的电压有较大范围的变化,就有必要提供母线电压的调节。
16.Analysis on Abnormality Temperature of the Up Seat in Low-voltage Side of Transformer电力变压器低压侧升高座温度异常的分析
17.IMPROVEMENT OF ANGLE STABILITY BY ADVANCED HIGH SIDE VOLTAGE CONTROL REGULATOR采用高压侧电压控制改善系统的角度稳定性
18.Analysis for Error Conclusion of Single Phase Fusing in Potential Transformer High-Voltage Side Fuse电压互感器高压侧熔断器一相熔断误判分析
相关短句/例句
side pressure侧压
1.Based on the heavyside pressure moving principle, the process ofside pressure is analyzed and the relationship between volumes ofside pressure and slab deformation after theside pressure is dis-cussed.从大侧压运动规律出发,分析了定宽机(SP)的侧压过程,并讨论了侧压后板坯变形量与侧压量之间的关
2.The effect of major parameters such asside pressure P, and relative bending radius R/H on curvature springback ΔR is studied, the law of interaction between P, R/H, ΔR and distribution and changing of tangential strain in deformation area is obtained, and thus, a scientific base is provided for design and modification of die and selection of technological parameters.通过绕弯试验和应变分析，研究了绕弯工艺的主要参数侧压Ｐ和相对弯曲半径Ｒ/Ｈ对曲率弹复ΔＲ的影响。
3)confining pressure侧压
1.Characters of the deformation and strength under differentconfining pressures on sedimentary rock;不同侧压下沉积岩石变形与强度特征
2.Rock failure process analysis code( RFPA2D) is used to research the rock specimen with two parallel and offset cracks, and main object is to study differentconfining pressure influence on propagation, coalescence and interaction of cracks in rock bridge area.应用岩石破裂过程分析程序分析了侧压对预制两个平行裂纹岩样中岩桥区裂纹的扩展、贯通和相互作用机制的影响,并对岩样。
4)lateral extrusion侧向挤压
1.The classification of the extrusion methods and the characterizes oflateral extrusion;挤压方法的分类及侧向挤压的特点分析
2.A rigid-plastic element-free Galerkin-finite element(EFG-FE) coupling method was developed for the numerical simulation of planelateral extrusion process.应用刚塑性耦合无网格-有限元法,对平面侧向挤压过程进行数值模拟。
5)siding press regulation侧压规程
1.Basing on the condition of differentsiding press regulations,simulated the distribution of rolling force,displacement nephogram and strain nephogram in different deform field systematically,the rules of rolling force and time were yeild.在不同侧压规程的前提条件下,模拟了不同变形区内轧制力、位移和应变的分布情况,得到了轧制力随时间变化的规律。
6)sizing press(SP)减宽侧压
延伸阅读
侧压承载强度分子式：CAS号：性质：板材和其他零件连接时，在板面上垂直钻孔，用销、铆钉、螺栓插入固定，在其上施加平行于板面的负荷时，板所承受负荷的能力。板材的破坏主要是由孔中的铆钉或螺栓挤压孔壁造成局部塑性破坏而发展造成的。该值可将打好孔的试样用螺栓和金属夹板连接，然后分别将它们夹持于拉力试验机的上下夹具上，开动拉力机以一定速度分离上下夹具直至试样被拉破，即可算得测压承载强度。
