900字范文,内容丰富有趣,生活中的好帮手!
900字范文 > 扭振控制 torsional vibration control英语短句 例句大全

扭振控制 torsional vibration control英语短句 例句大全

时间:2019-09-21 21:54:54

相关推荐

扭振控制 torsional vibration control英语短句 例句大全

扭振控制,torsional vibration control

1)torsional vibration control扭振控制

英文短句/例句

1.Study on Torsional Vibration of a Flexible Manipulator Featuring Piezoelectric Actuator;基于压电驱动器的柔性臂扭振控制研究

2.Controlling the Pitch of Automobile Body When Braking by Means of Adjusting the Pre Fastened Angle of Torsion Bar Suspension调节扭杆悬架预扭角控制汽车纵向角振动

3.Analysis and Control on Engine Cranktrain Torsional Vibration;汽车发动机曲轴扭转振动分析及控制

4.Experimental Investigation on Torsional Vibration Measurement and Control of Rotor Shaft System;转子轴系扭振测量与控制的实验研究

5.Study on Torsional Vibration Control of a Flexible Bar Using Piezoelectric Torsional Actuator;压电扭转驱动器及其在柔性杆扭转振动控制中的应用研究

6.The Torsion Response Control Method of Complex High-rise Building with Large Local Space;局域大空间高层结构扭转振动控制方法

7.MTMD for Torsional Vibration Control of Tall Building Structures under Seismic Actions;MTMD对地震作用下高层结构扭转振动的控制

8.The results show that the Circular Tuned Liquid Column Damper( CTLCD) is an effective torsional response control device.结果表明,环形调液阻尼器是一种有效的扭转振动控制装置。

9.Torsional Vibration Control of Complex-shaped Tall Structures under Earthquake Using Tuned Liquid Damper;调谐液体阻尼器对地震作用下复杂体型高层结构扭转振动的控制

10.Coupled Stability Analysis of the Helicopter"s Engine Control System and Mechanical Vibration System Based on LabVIEW基于LabVIEW的直升机发动机控制—机械扭振系统耦合稳定性分析

11.Study on the Producing Mechanism of Torsional Vibration Noise and Controlling Ways汽车传动系扭振噪声的发生机理及控制方法探析

12.torsional damper扭振减振[阻尼]器

13.Development of Elastic Couoling Torsional Vibration Test System弹性联轴器扭转振动测试系统的研制

14.A new explanation of operation principle about RFC polarization-state control device is presented, which includes the effects of twisted fiber.本文考虑了光纤被扭转的效应,对可转式光纤曲柄偏振控制器工作原理给出了新见解。

15.Torsional vibration absorbersGB/T16305-1996扭转振动减振器

16.torque control air impact wrench扭矩控制空气冲击式扳手

17.It is hard work to control the workings of inclination and turn the bent of nature.要控制癖好,扭转天性,是困难的。

18.Once inflation gets out of control it will be harder to wring out of the system.一旦通胀失去控制就很难扭转乾坤了。

相关短句/例句

torsional vibration control扭转振动控制

1.The criterion for searching the optimum parameters of AMTMD fortorsional vibration control is defined as the minimization of minimum values of maximum torsional displacement dynamic magnification factors of an asymmetric building with AMTMD.用于不规则建筑扭转振动控制AMTMD最优参数准则定义为:设置AMTMD不规则建筑的最大扭转角位移动力放大系数最小值的最小化。

3)Torsional vibration control experiment扭振控制实验

4)anisotropy / torsional vibration control各向异性\扭振控制

5)torsional vibration suppression扭振抑制

6)torque control扭矩控制

1.Based on existing technologies,This article introduces thetorque control capability eval-uation methods for different types of tightening tools such as hand torque tools,electrical tighten-ing tools and pneumatic tightening tools.基于当前技术水平,介绍了人力扳手、电动拧紧工具、气动拧紧工具等不同类型拧紧工具的扭矩控制能力评价方法。

延伸阅读

轴系扭振轴系扭振torsional vibration of shaft systemZh0Ux一nltjzhe自轴系扭振(torsional vibration of shaft sys-tem)汽枪发电机组轴系的扭转振动,简称扭振。当轴系传递力矩时,在其各个断面上因其所受扭矩的不同而产生不同的角位移。当扭矩受到干扰,如扭矩瞬时变化、扭矩突然卸去或加载时,则轴系产生按其固有扭振频率的扭转振动。事实上轴系驱动发电机的扭矩始终存在着周期性的变化,即强迫扭振,因其振幅不大,不致引起危害。但遇到大的干扰扭矩,或干扰扭矩的频率与轴系固有扭振频率共振时,则会产生轴系或长叶片的损伤或断裂。为防止扭振损坏设备,转子设计阶段就应对轴系扭振频率进行核算,并使之避开工作频率及其倍频的一定范围。为了验证计算的可靠性,尚需在运行机组上进行实测。原因扭振导致设备损坏的起因是,在不利的悄况下,电力系统的电气性能与汽轮发电机组轴系的机械性能互相影响而引起机电藕合共振,或者由于电力系统故障使转子承受过大的扭矩所造成。这种机电性能互相作用的影响有次同步共振、超同步共振和电力系统故障三类。次同步共振现代大容量汽轮发电机组轴系的固有低阶扭振频率常常低于工频。电网是由电阻、电感和电容组成的电气回路,本身存在固有的电气自振频率。远距离高压输电线路上往往采用申联补偿的办法以提高其输送容量。当采用串联补偿以后,电网的自振频率降低。如果遇有扰动,电网的自振频率与电网的工频相1减,形成拍频作用在发电机上,可使轴系产生强迫扭振。此强迫扭振频率如与轴系固有扭振频率相同而共振时,称为次同步共振。此时扭振振幅不被衰减,可能使轴系某一断面造成疲劳损伤而破坏。超同步共振又称倍频共振。当发电机三相负荷不平衡时,发电机每旋转一周,轴系扭矩有两次变化,即轴系扭矩受两倍工颇的干扰。如果轴系的固有扭振倾率或转子上的部件如叶片的振动频率也是两倍工频,则可能引起轴系超同步共振的危害。电力系统故障当发电机母线或外部线路发生短路故障,或故降消除,或开关操作,或重合闸动作,或非同期并网等,都会使轴系扭矩瞬时增大,可能超过设计值或引起轴系大幅度扭振而导致严重后果。研究进屁近十余年来世界各国对系统干扰与轴系安全问题进行了大量研究工作。目前理论问题已解决,可计算轴系固有扭振频率,并根据轴系材料性能估算大轴的液劳寿命消耗。欧美等国还研制了成套的在线监侧仪器安装在系统中,捕捉了事故下的各种电气和机械参数,包括轴系所经受的扭矩。实测结果认为:(1)次同步共振可使大轴的疲劳寿命消耗达100%,即一次就能造成损伤,故应极力避免。如采取措施可使每次事故的疲劳寿命消耗降到l%以下.(2)超同步共振应尽力避免。(3)过去认为发电机出口处三相短路时主轴扭矩最大,但实验结果证明非同期并网和故障消除时的扭矩比它大许多倍,特别三相重合闸动作时有可能使主轴疲劳寿命消耗达100%,应绝对避免。

本内容不代表本网观点和政治立场,如有侵犯你的权益请联系我们处理。
网友评论
网友评论仅供其表达个人看法,并不表明网站立场。