液态压铸,liquid die casting
1)liquid die casting液态压铸
1.The microstructure and mechanical properties of the products made of A380 aluminum alloy by two different forming methods(semi-solid die casting andliquid die casting) are studied under state of casting and T6 heat-treatment.经过同样的T6热处理后,半固态压铸件的抗拉强度有所提高,液态压铸件的抗拉强度却下降很大。
2.The microstructure and mechanical properties of the products made of A380 aluminum alloy by the two different forming methods(semi-solid casting andliquid die casting) with the state of casting and T6 heat-treatment have been studied.经T6热处理后,半固态压铸件的抗拉强度有所提高,液态压铸件的抗拉强度却下降很大;两者的延伸率均有所下降,其中液态压铸件的延伸率下降幅度较大。
英文短句/例句
1.Friction and Wear Characteristics of AZ91D Magnesium Alloy Formed by Rheo-diecasting and Die Casting Process流变压铸与液态压铸成形AZ91D镁合金的摩擦磨损性能
2.Numerical Simulation of AZ91D Motorcycle Engine Shell during Liquid Die Casting Filling Process;AZ91D摩托车发动机壳体液态压铸充填过程数值模拟
3.Quadratic Optimal Control on Dynamic Soft-reduction Hydraulic System of Continuous Caster连铸机动态轻压下液压压下系统的最优二次型控制
4.Research on Thickness of Gas Interspace When Liquid Metal Flows in Process of Pouring in Expendable Pattern Casting消失模负压铸造液态金属流动前沿气隙的厚度研究
5.Microstructures and Mechanical Properties of As-Cast and Die-Cast Mg-Al-Nd Magnesium Alloys铸态和压铸态Mg-Al-Nd镁合金组织与力学性能
puter Simulation of Liquid Metal Flow into Diecasting Cavity压铸型腔金属液流动的计算机模拟
7.The Investigation of Counter-Gravity Casting Control Technology;反重力铸造液面加压控制技术的研究
8.Numerical Study of the Liquid Core Reduction for Thin Slab Continuous Casting;薄板坯连铸液芯压下过程的数值仿真
9.Numerical Study of the Liquid Core Reduction for Thin Slab Continuous Casting薄板坯连铸液芯压下过程的数值模拟
10.Solid-liquid Mixed Die-casting of Al-10%Cr AlloyAl-10%Cr合金的固液混合压铸工艺
11.Process Parameters Design of Semisolid Squeeze Casting for Producing White Cast Iron Milling Ball白口铸铁磨球半固态挤压铸造工艺参数设计
12.Analysis and Countermeasures of Fluid Contamination to Slab Continuous Caster Oscillator Hydraulic System板坯连铸振动液压系统油液污染分析及对策
13.The Single Chip Microcomputer Control For Liquid Level Pressurization System of Low-pressure Casting低压铸造液面加压系统的单片微机控制
14.Liquid Steel Solidifing State Analysis in Mould the C C.slab板坯连铸结晶器内钢液凝固状态分析
15.Investigation on Technique of Rheo Die-casting for Semi-Solid A380 Aluminum Alloy;A380铝合金半固态流变压铸工艺研究
16.The Research on the Semi-solid Diecasting Processing of AZ91D Magnesium Alloys;AZ91D镁合金半固态压铸工艺研究
17.Study on Semi-Solid Aluminum Alloy Rheo-Die-Casting Technique;半固态铝合金熔体流变压铸工艺研究
18.Microstructure in as-cast AZ61 magnesium alloy during hot compression deformation铸态AZ61镁合金热压缩变形组织变化
相关短句/例句
solid die casting固态压铸
3)Die Casting Trend压铸动态
4)hydraulic pressure casting液压件铸件
1.As for thehydraulic pressure castings,there are many special characteristics in the production,structure and core-making process.液压件铸件的生产性质、结构性质及具体的生产工艺均与其它行业的铸造生产有所不同,文章通过对国内现有液压件铸件生产行业的调查研究,根据液压件铸件生产批量小、品种多及质量要求高的特点,对熔炼技术中出铁温度、成分控制、造型工艺、制芯工艺、砂处理及清理等主要生产因素初步分析,探讨液压件铸件质量的影响。
5)iron casting hydrau lic cylinder铸铁液压缸
6)semi-solid die casting半固态压铸
1.The process parameters ofsemi-solid die casting of A356 aluminum alloy have been studied systematically in simple plate mould with different thickness.应用具有不同厚度的简单板材模具来系统研究压铸工艺参数对A356铝合金半固态压铸件性能的影响,以优化半固态压铸工艺及其参数。
2.In this paper, the relationship between the gate shape and the filling procedure of complex cavity duringsemi-solid die casting has been simulated in detail by modified finite element software of ANSYS.使用二次开发的ANSYS有限元软件,对铝合金半固态压铸复杂件的充型过程与模具内浇道形貌之间关系进行详细的计算机仿真。
3.The microstructure and mechanical properties of the products made of A380 aluminum alloy by two different forming methods(semi-solid die casting and liquid die casting) are studied under state of casting and T6 heat-treatment.对A380铝合金液态与半固态压铸成形件在压铸态和T6热处理态下的力学性能与微观组织进行了研究。
延伸阅读
J1113压铸机操作规程理论生产率：180次/时1、遵守《铸造设备通用操作规程》有关规定。2、检查油箱内的机油量，如果油面低于油标的上限部位，就加入干净的20号机械油。3、一般不准空压射，如必须空压射时，一定要在压射室中放入软质垫料（如棉丝、铅块等），以防损坏设备。4、按下面顺序起动设备，进行空载试车：a、 打开贮压缸伐和它上端的两个小截门；b、 拉出手操纵伐的的柄；c、 打开空气开关，接通电源，转动主令开关，使设备能点动运转；d、 启动电动机，待其运转正常后，再推入手柄操纵伐的手柄，使高压泵升压，然后按动各电钮，点动试车。设备经过空运转，确认一切正常后，方可进行生产。5、切实注意安全，操作者必须穿戴好劳保用品，不得站在正对着压铸分型面的部位，以防铝溅出，发生烧伤事故。6、经常观察各种仪表读数是否符合工艺要求，设备的运动是否正常，如发现异常现象，立即按动中停按钮或停泵按钮，然后对设备进行检查。必要时，通知维修人员修理。7、经常注意液压油的温升，油温量最设法得超过55°С，否则开动冷凝器进行冷却。1、 设备停歇一小时以上时，必须切断电源，关闭贮压伐，防止产生错误动作和消耗贮压缸压力。2、 工作后，按下列顺序停车：先拉出手柄操作伐的手柄，然后关泵停车，切断电源，接着关闭贮压缸伐及其上端的两个小截门，并堆入手柄操纵伐的手柄。10、设备清理后，设备的运动部分（如缸杆、导杆、滑轨等）还须涂一层薄机械油。
