固定球阀,fixed ball-valve
1)fixed ball-valve固定球阀
英文短句/例句
1.The metal hard seal fixed on the ball valve divides into the normal temperature and the high temperature, when the application temperature is higher than180℃, please indicate the application temperature the first.金属硬密封固定球阀分为常温型和高温型，当使用温度大于180℃，订货时应注明使用温度。
2.Lift out the disc holder assembly from the body of the valve.从阀门的阀体内提起阀瓣固定器总成。
3.To reverse the seat disc, unscrew the disc screw and disassemble the disc washer and disc rubber from the disc holder assembly.为了翻转阀座阀瓣，则要拧松阀瓣螺丝，从阀瓣固定器总成拆解阀瓣垫圈和阀瓣橡胶。
4.The use of seat screws as a retention method is prohibited.禁止采用阀座螺丝作为固定阀座的方法。
5.Outer row of studs secures the yoke to the body.双头螺栓的外部排列将阀架固定在阀体上。
6.In all designs, the valve stem normally serves as a piston rod with disc fastened directly to them.在所有结构中，阀杆通常作为活塞杆，阀瓣直接固定在阀杆上。
7.Throttle Body Mounting Bolts—Engines—Typical节气阀体固定螺栓—引擎—典型的
8.Throttle Position Sensor Mounting Screws节气阀位置感知器固定螺丝
9.Solenoid Switch Valve Latched in TCC Position电磁螺线管开关阀门固定在ＴＣＣ位置
10.Anchor/support bolt holes are located in base of body.固定器/支架螺栓孔位于阀门的基座。
11.Type of valve- gate, globe, check, etc.阀门种类：闸阀，截止阀，止回阀，蝶阀，球阀，等等。
12.The relief valve cover shall be secured with stainless steel bolts and shall utilize a quarter-turn locking joint to capture the spring load of the relief valve.安全阀阀盖应该采用不锈钢螺栓紧固，应该采用四分之一转锁定连接来所定安全阀的弹簧负载。
13.The valve cover shall be held in place through the use of a single grooved style two-bolt coupling.阀盖应该通过单个沟槽状双螺栓联结器固定住。
14.The PCV valve sticks in the open, maximum-flow position.把PCV阀固定在开启位置即最大流量位置。
15.We need an eye bolt to fit this valve.我们需要一个有眼螺栓来固定这个阀门。
16.Experimental and Numerical Study of Flow Field on Folded-Downward Edge Fixed Valve Tray;折边固定阀塔板流场的实验研究和数值模拟
17.Experimental Study and Numerical Simulation of Hydrodynamics Performance for Gas Passing Through the Fixed-Valve;气体穿过固定阀的流体力学性能及数值模拟
18.The designing of 6.0MPa electric actuator cylinder head valve for CO_2 fixed extinguishing systemCO_2固定式灭火系统6.0MPa电动气瓶阀的设计
相关短句/例句
Fixed ball valve固定式球阀
3)fixed valve固定阀
1.Determination of optimal jumping height offixed valves of sucker rod pumps and its field application;抽油泵固定阀球最佳跳动高度的确定
2.Gas flow field on folded-downward edgefixed valve tray was simulated by turbulence models and FLUENT 6.2软件和湍流模型对气流通过折边固定阀塔板气相流场进行了数值模拟,并将模拟结果与通过热线风速仪的测定结果进行对比。
3.Structure and operating performance of newfixed valve tray with suspending downcomer (DJ - 5 tray) was introduced.新型固定阀悬挂降液管塔板是一种新型大通量高效DJ塔板。
4)standing valve cover固定阀罩
1.Development and application of thestanding valve cover;抽油泵高效固定阀罩的研制与应用
5)Fixed-cone valve固定锥阀
1.The numerical simulation was used to the flow near theFixed-cone valve,in the hood and the downstream pipeline in the water release for the Bakun Hydropower by applying 2-D and 3-D RNGκ-εturbulence model.本文以马来西亚巴贡水电站放水孔作为研究背景,分别采用了二维和三维的RNGK-ε紊流数学模型,对放水孔内部固定锥阀、消能罩及部分下游管道内的流场进行数值模拟,在求解离散方程的时候采用的是比较成熟的PISO算法,对于自由表面的处理采用两相流中的VOF法。
6)standing valve固定阀
1.Research and application ofstanding valve assembly on tube pumps for blockage for prevention;普通管式泵防堵塞固定阀的研究与应用
2.The barrel,plunger andstanding valve of the pump were designed,improving the barrel\"s force conditions and reinforcing the screw thread\"s sealing performance and tensile strength.该泵对泵筒、柱塞、固定阀做了设计,改善了泵筒受力状况,提高了螺纹的密封性能和抗拉强度。
延伸阅读
固定①不变动或不移动的（跟‘流动’相对）：～职业丨～资产。②使固定：把学习制度～下来。
