轴承加热器,bearing heater
1)bearing heater轴承加热器
2)induction type bearing heater感应式轴承加热器
3)sealing heater轴封加热器
1.Practical approach to hydrophobic recovery of thesealing heater for self-equipped thermal plants自备热电厂轴封加热器疏水回收方法
英文短句/例句
1.Practical approach to hydrophobic recovery of the sealing heater for self-equipped thermal plants自备热电厂轴封加热器疏水回收方法
2.spindle inner oil seal(平衡器) 轴内油封
3.Study on Theory and Technology of Bearing Inner s Induction Heater;轴承内环感应加热器理论与技术研究
4.The technology of the mainshaft sealed apparatus has got the state patent it has two funetions of electric and steam heating.主轴密封装置获国家主利。具有电、汽两种加热功能。
5.The cooling/ heating media is connected to the rolls through rotary joints with ball bearing and carbon seals for a leak free operation.冷却/加热介质由旋转接头和辊连接，球轴承和密封圈保证不会泄漏。
6.CALCULATION OF WATER-WATER MIXING HEAT EXCHANGER USED IN HOT WATER BOILER集中供热热水锅炉用轴向式水-水混合式加热器的计算方法
7.Parameters optimization of fillet weld sealing joint in high pressure hydrogenation heat exchange加氢换热器角焊缝密封接头焊接工艺参数优化
8.Introduction the on-line Process Method of Electric Joint Slack for Heat Rolling and Finish Rolling浅谈热轧精轧电机联轴器在线加工方法
9.sealing regenerative-type air preheater密封回热式空气预热器
10.hot water heater热水加热器热水供暖器
11.deaerating heater除气加热器除氧加热器
12.Biaxially oriented polypropylene film for heat-sealGB/T12026-1989热封型双轴拉伸聚丙烯薄膜
13.non-enveloped thermistor非密封型热敏电阻器
14.bearing over-heat protective relay轴承过热保护继电器
15.A closed metal vessel having a spigot and used for warming or serving tea or coffee.壶封闭的有塞的金属容器，用于加热或端茶或咖啡
16.Canning (1809): Method of preserving food from spoilage by storing it in containers that are hermetically sealed and then sterilized by heat.罐藏法:将食品贮藏于密封的容器中然后加热消毒的食品防腐方法。
17.Welding Process Test and Application of Bottom Head and Heater Sleeve in Pressurizer稳压器下封头与加热套管的焊接工艺试验及应用
18.Thermal Analysis of LED Packages based on Heat Pipe Heat Sink基于热管散热的LED器件封装热分析
相关短句/例句
induction type bearing heater感应式轴承加热器
3)sealing heater轴封加热器
1.Practical approach to hydrophobic recovery of thesealing heater for self-equipped thermal plants自备热电厂轴封加热器疏水回收方法
4)bearingalarm轴承过热报警器
5)Clutch heating box联轴器加热箱
6)shaft seal leakage heater轴封漏汽加热器
延伸阅读
齿轮联轴器由带有内齿、凸缘的外套筒和带有外齿的内套筒组成的可移式刚性联轴器(见图)。内套筒的轮毂分别与主动轴和从动轴联接；两个外套筒在凸缘外通过螺栓固结在一起。工作时，内齿与外齿作啮合运动。内、外齿多采用压力角为20°的渐开线齿形，齿侧间隙较一般齿轮副大。外齿顶圆母线制成球面，球面中心在齿轮轴线上，因此具有补偿两轴轴线的相对径向、轴向、角度位移的特性。为了改善齿的接触条件，提高联轴器承载能力，增大两轴的许用相对角位移，可采用鼓形齿，即将外齿齿宽方向上的节圆和根圆由直线改为圆弧，使齿的截面呈鼓形，以减轻或避免由于轴线偏斜带来啮合面的干涉和接触不良。鼓形齿的圆弧度还可由不同曲率半径的圆弧组成，以得到适用不同大小的轴线偏斜的最佳齿形。齿轮联轴器有较多的齿同时工作，外形尺寸小，承载能力大，在高速下工作可靠。薄壳圆筒型中间齿套齿轮联轴器能适应的转速高达 20000转/分。鼓形齿联轴器在高速、重载机械上得到广泛采用，具有无轴向窜动、传动平衡、冲击振动和噪声小等特点，但加工工艺比较复杂，成本较高。为提高齿轮联轴器的性能和寿命，在工作状态下必须有良好的润滑，必要时应采取连续喷油和强制润滑。
