挤出物,extrudate
1)extrudate[iks"tru:deit]挤出物
英文短句/例句
1.Study on the Melt Graft-Reacting Extrution of PE or EPDM with MAH and the Alloying of PA Toughened by the Grafts;MAH与PE或EPDM熔融接枝反应挤出和挤出物增韧PA合金化的研究
2.THEORETIAL PREDICT AND EXPERIMENTAL RESEARCH OF PRODUCT DIAMETER IN GAS-ASSISTED EXTRUSION气辅挤出成型中挤出物直径的理论预测和实验研究
3.These asisted extrusion technologies had significant effects on improving extrusion rate and product quality, and decreasing energy consumption.这些辅助挤出技术对提高挤出速率和挤出物质量、低能耗具有重要意义。
4.Research on Mechanism of Pricision Extrusion the Effect of Technology Factor on Pricision Extrusion;高聚物精密挤出机理初探（一）影响高聚物精密挤出的工艺因素
5.Research on Mechanism of Precision Extrusion the Effect of Equipment Factor on Pricision Extrusion;高聚物精密挤出机理初探（二）影响高聚物精密挤出的设备因素
6.On-Line Measurement and Control of the Flow in Precise Extrusion of Polymers聚合物精密挤出过程中挤出流量的在线测量及控制方法
7.To exude or give off(matter)in drops or small quantities.使挤出；使滴下以点滴或少量的渗出或排出（物质）
8.An object or material produced by extruding.压出品经过挤压而产生的物体或材料
9.wedge a thing off [away]把某物强行推开 [排挤出去]
10.The entire cell is extruded and constitutes the secretory product.整个细胞被挤出形成分泌产物。
11.THE FLOW ANALYSIS OF POLYMER MELT IN CO-EXTRUSION DIE共挤出机头中的聚合物熔体流动分析
12.The Synthesis and Characterization of Compatibilizator Using the Reaction Extrusion of Polymers;聚合物反应挤出相容剂的合成与表征
13.On-Line Ultrasonic Monitoring Transducer for Polymer Blending聚合物挤出在线超声监测传感器研究
14.Continuous Extrusion Foaming of Polypropylene/ Polydimethylsiloxane BlendPP/PDMS共混物的连续挤出发泡成型
15.To squeeze the juice or other contents from.挤压从…中把果汁或其他内容物压榨出来
16.Simulation of Flow Instability of Polymer in Extrusion Die在挤出机口模中聚合物不稳定流动的模拟
17.Phenomenological Studies on Extrusion Swell of Polymer Melt Through Conical Short Dies;聚合物熔体在圆锥短口模的挤出胀大唯象研究
18.The Melt Flow Instability of LLDPE, LDPE and Their Blends at High Speed Extrusion;LLDPE、LDPE及其共混物高速挤出流动不稳定性的研究
相关短句/例句
extrudate[iks"tru:deit]挤出物、挤制材料
3)Polymer extrusion聚合物挤出
4)extrudate appearance挤出物表观
1.The differences between these two sorts of polyethylene were investigated by analyzing pressure oscillations,flow curves andextrudate appearances.通过压力振荡图、流动曲线和挤出物表观3方面,对两种类型聚乙烯压力振荡的差异进行了分析。
5)Starch extrudate淀粉挤出物
6)extrusion material quality挤出物质量
延伸阅读
挤出物胀大分子式：CAS号：性质：当高聚物熔体从小孔、毛细管或狭缝中挤出时挤出物在挤出模口后膨胀使其横截面大于模口横截面的现象。定量上用胀大比来表示。挤出物胀大在聚合物熔体中是常见的，这是由于聚合物熔体在模具内因流动而取向，在流出模口时分子重新蜷曲。挤出物胀大随切变速度增大而增大，在到达最大值后再下降。分子量增大和其他能增加缠结的因素(如长支链的增加)都将使挤出物胀大增大。
